This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

The 6al delivers everything the 6a does with the addition of a built-in soft touch rev control. This feature allows you to set an rpm limit to protect the engine from over-rev damage caused by driveline failure or missed shifts. Other msd rpm controls can be connected to the 6al such as a three step module selector or rpm activated switch . The 6al also comes supplied with rubber shock mounts and 3000, 6000, 7000, 8000, rpm modules. All necessary parts and wiring instructions are included.

Note: some applications may require msd tach adaptor, part number r8920.

Operating specifications: operating voltage: + 10-18 vdc, negative ground; current requirements: 5 amps-5,000 rpm, 10 amps-10,000 rpm; rpm range:...(choose a part on the right to read more)

General Fitment

Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)

The radiator is a critical engine component that needs to be inspected and cleaned of debris to keep them functioning efficiently. If damage is noticed, replace it with this hello OEM high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the upper and lower rubber mounts, part # 99110653701 and 99110653802 sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. This part is the latest supersession and can also be used in place of part number 991 106 138 01.

This item may need to be sourced from ge...(choose a part on the right to read more)

The rs model engine mount is not a hydro-elastic mount like most models. It contains a rubber core with an 85-shore hardness value. That equates to a more responsive chassis and improved shifting response. A perfect compromise for street and track use as it is more forgiving than aftermarket solid mounts. Sold individually. 2 necessary per car. To install these mounts on any model 964 / 965 / 993 and 993 tt, we recommend our rs engine mount set that includes 2 mounts and all the mounting hardware, part # FVD375964

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Introducing the latest in tow hook innovation: engineered with an increased side load capacity and adjustable-length rigid mount receiver. This tapered stainless loop design incorporates a new locking function to maintain your preferred loop position. Additional features include machined graphics, rotational timing and camera mount compatibility.

Rennline's stainless steel folding race hooks install in minutes on any Porsche with factory screw type removable tow hooks. Unlike the aluminum units on the market that are usually advertised as "for decorative purposes only", rennline's stainless steel tow hooks are precision machined and will stand up to the extreme abuse seen in any race environment. These p...(choose a part on the right to read more)

The oil cooler suffers from exposure to road debris, the elements and corrosion with age. It is a critical engine component, that should be replaced when any leaking is detected. This kit is ready for installation with oil cooler, oil pipes, new rubber mounts, brackets and an oil drain plug. It is a high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This kit is a direct replacement kit for original part # 930 207 053 00 and current part # 93020705304. Complete the installation with our complete stoneguard kits part # FVD20705301 and FVD20705302

This item may need to be sourced from Germany and would take 2-4 ...(choose a part on the right to read more)

Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)

Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 wee...(choose a part on the right to read more)

Sold as a set of (2) upgrade your soft rubber engine mounts with our solid engine mounts. - precise shifting - better throttle response - cnc machined aluminum - sold as a pair with all mounting hardware - more responsive chassis - made in Germany note: you feel more vibration and hear more noise with solid mounts.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. We can offer your c4 a more sporty feel without the harsh vibration from a solid mount. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). The rs spec shore rubber offers the c4 sportier handling without being too stiff for street use. Be sure to swap yours out during the next service. Sold individually. Central fitment into the transmission carrier bracket 96437502301. 1 qty. Required. Tech tip: now is the ti...(choose a part on the right to read more)

Re-engineered and tig welded from chrome-moly steel,the quick six mounting kit enables you to immediately bolt a six-cylinder engine into your 914-4, using the factory engine pods. the '73-76 bodies, however, do require the purchase of the early rubber engine mounts. The bulkhead mount is for the serious six conversion. Welded in by a competent mechanic, it allows you to eliminate the four cylinder mounting pods allowing more clearance for valve adjust, easy removal of the rear shift bar and most importantly shifts the center of weight further forward to the factory recommended position. Powder coated finish.